oval classes and rules

STOCK SLASH CHASSIS

NO LCG CHASSIS

STOCK BODY

12T MOTOR & XL-5 ESC OR HOBBYWING JUSTOCK 13.5 COMBO OR TRAXXAS BL 2S SYSTEM

2S LIPO BATTERY 8.4

STOCK TIRES, YOU CAN CHANGE FOAMS & WHEELS

YOU MAY USE SOME TRAXXAS ALUMINUM UPGRADES, NOT ARMS OR SHOCK TOWERS

YOU MAY USE SOME RPM UPGRADES, NOT TRANSMISSION

WEIGHT MINIMUM 2098

Maximum Overall Length: 18”

 Maximum Chassis width: 4.025"

Cage – Sprint cars must have a scale appearing contemporary cage made out of rounded stock. The cage must be symmetrical left to right and mounted level to the chassis. Unrealistic shaped cages designed to exploit the rules below are not permitted. Maximum cage width at driver halo, down tubes, and top frame rail: 3.600". Maximum cage height 5.5" from top of chassis to top of cage at highest point. Rear “down tubes” must slant forward. All cage and body components such as cage, bumpers, nerf bars, hoods, side panels, tanks, etc. must be mounted on the centerline of the cage. Chassis may not extend outside of the side panels by more than 1/4" on either side.

Bumpers – A flat, curved or tubular front bumper (or combination of) must be used and may not be designed to direct air or create downforce. Maximum height of front bumper is 1.75” from the bottom of the lowest point of the chassis. Scale appearing side nerf bars must be used on both sides of the car (left side of nitro sprint is optional due to clearance needed for nitro exhaust). A scale appearing rear hoop style bumper must be used. Bumpers and nerf bars must be made of rounded stock with no sharp edge

Tail tank – A traditional scale appearing rounded style three dimensional rear fuel cell must be used.

Headers - Three dimensional scale appearing exhaust headers must appear on both sides of car in “engine area

Side panels – Flat side panels may be made from molded or fabricated polycarbonate. Maximum height of side panels in front of the driver cockpit is 3.80” from the bottom of the chassis. Must have minimum of 3/4" high by 2.5" long openings on both sides of cage in driver compartment. Additional material may be used/added to either side of the side panel openings to replicate a scale appearing driver but may not exceed 1" x 1". (Note that the top wing mounts may cover these openings for winged classes.) Side panels may not extend beyond the rear of the cage by more than 0.25”. Side panels may not extend above or in front of the front downtubes. Side Panels may not extend into the area that is behind the rear axle AND below the top of the rear nerf bar. Scale appearing driver arm guards and engine vents may be used but cannot extend more than 3/8" from the side panels. No other flares or turnouts designed to deflect, trap and/or form a pattern for air to travel in a directed manner are permitted except for those used to cool electronics.

Hood Area – A scale appearing hood must be used and is defined as beginning at the front axle and ending at the front of the driver cockpit. The hood must be symmetrical from left to right. The hood must be tall enough and wide enough to allow room for a scale engine intake and air cleaners (no unrealistically low or flat hoods). Minimum vertical gap from top of hood to bottom of front cage crossbar: .750". The hood may not drop below the nearest point of the side panels by more than 3/8” and may not have any channels more than 0.25” deep designed to trap or direct air.

Nose Area – A molded or fabricated nose piece may be used and is defined from the front axle forward to the front bumper. Front bumper may not extend more than 3” from front axles. Nose piece (any Lexan) must be at least ¼” back from the leading edge of the front bumper. Maximum width of nose piece/bumper is 3.75". Maximum width of any surface designed to add downforce is 3.125”. Nose piece may not extend above the cage downtubes or an imaginary line connecting the downtubes if the cage is a split design.

Front wing/mounts – For front wing dimensions see appropriate wing drawing pdf. The front wing center section may not extend in front of the front bumper. Front wing mounts may be made of Lexan but may not exceed 1.75” in length and 1.75” in height and may not extend in front of or behind the center section of the wing.

Top wing/mounts – For top wing dimensions see appropriate wing drawing pdf. Top wing minimum height at leading edge: 5.00" from bottom of chassis. Top wing maximum height at leading edge: 6.50" from bottom of chassis. Center section and side panels must be made from at least 3 separate pieces of polycarbonate, carbon or aluminum material. All corners and edges must be rounded and free of sharp edges. Main and Front wings must be mounted so that they are centered on cage, no offset wings. Wing center sections must have all 4 corners set at 90 degree angles, no canted or angled panels. Wings must also be mounted level from side to side. Center section of wing may not extend beyond leading or trailing edge of side panels. Side panels must have braces that hold side panel rigid at 90deg. to center section during race conditions. Two braces are required from top of the center foil to the left sideboard and one brace is permitted below the center foil to the right side board. Braces can be a maximum of .750" wide and front edge of front brace must be no more than 1.5” back from side panel leading edge. Side Panels may have front, back, top and bottom turnouts of no more than .375" and are included in max dimension. Flat foil center sections will be allowed a .250” turndown at the leading edge.

 Visors - A scale appearing visor may be used on any wingless sprint car. The visor must be flat and follow the contour of the front downtubes. No wider than the width of the downtubes where it is attached and no longer than 1".

 No additional Lexan or any other material may be mounted to nerf bars, bumpers, cage, wing or any other part of the car that will trap, alter, or direct air flow for the purpose of gaining an aerodynamic advantage.

Top wings are mandatory and 7x7. Front wings are optional for all sprint classes.

Tires any 2.2 buggy wheel and rubber tires.

Battery 2S lipo max voltage 8.4 volts

Motor & Esc are open and ROAR Approved

Same rules as sprint EXCEPT 13.5 Hobbywing JustStock motor and ESC

• No sidewing

·       Tires:

o   Stock Traxxas tires, you can change wheels & foams.

·       Motor:

o   Traxxas 12T motor or Hobbywing 13.5 Justock fixed timing motor or Traxxas BL 2S system

·       ESC:

o   blue Traxxas XL-5 esc or Hobbywing Justock fixed timing ESC

·       Battery:

o   Any 2s Lipo at 8.44 VDC maximum

o   Battery must be mounted in center of chassis in stock location

·       Chassis:

o   Stock Slash 2wd HCG chassis only

·       Stock Slash shocks only

·       Any Traxxas white progressive spring is allowed

·       Stock Slash 2WD transmission only

·       No ball diffs

·       No diff lockers

·       Stock Slash slipper clutch must be used and most function as stock

·       Slash spur gears only

·       RPM replacement parts are allowed, no RPM transmission

·       All suspension parts must be used in original mounting location. Left on left, front on front, etc.

·       Body:

o   Any late model body may be used, subject to race director approval. Body may be decked on a flat plane. Spoiler can be a 2” maximum off the deck lid. End caps maximum size 1.5” x 3”. Maximum body dimensions to be 13” wide by 8” tall by 26.5” long

·       No AVC, gyros, traction control, or other driving assist may be used.

·       All cars are subject to tech inspection at any time.

·       Tires:

o   Any track approved short course truck tire.

·       Motor:

o   Traxxas 12T motor or Hobbywing 13.5 Justock fixed timing motor or Traxxas BL 2S system

·       ESC:

o   blue Traxxas XL-5 esc or Hobbywing Justock fixed timing ESC

·       Battery:

o   Any 2s Lipo at 8.44 VDC maximum

o   Battery must be mounted in center of chassis in stock location

·       Chassis:

o   Stock Slash 2wd HCG chassis OR LCG Chassis

·       Stock Slash shocks only

·       Any Traxxas white progressive spring is allowed

·       Stock Slash 2WD transmission only

·       No ball diffs

·       No diff lockers

·       Stock Slash slipper clutch must be used and most function as stock

·       Slash spur gears only

·       RPM replacement parts are allowed, no RPM transmission

·       All suspension parts must be used in original mounting location. Left on left, front on front, etc.

·       Body:

o   Any late model body may be used, subject to race director approval. Body may be decked on a flat plane. Spoiler can be a 2” maximum off the deck lid. End caps maximum size 1.5” x 3”. Maximum body dimensions to be 13” wide by 8” tall by 26.5” long

·       No AVC, gyros, traction control, or other driving assist may be used.

·       All cars are subject to tech inspection at any time.

STOCK SLASH CHASSIS

NO LCG CHASSIS

STOCK BODY

12T MOTOR & XL-5 ESC OR HOBBYWING JUSTOCK 13.5 COMBO OR TRAXXAS BL 2S SYSTEM

2S LIPO BATTERY 8.4

STOCK TIRES, YOU CAN CHANGE FOAMS & WHEELS

YOU MAY USE SOME TRAXXAS ALUMINUM UPGRADES, NOT ARMS OR SHOCK TOWERS

YOU MAY USE SOME RPM UPGRADES, NOT TRANSMISSION

WEIGHT MINIMUM 2098

·         Any 2WD Buggy chassis in stock form (no cutting of the chassis)

·         Any 1/10 Buggy wheels and tires with any insert.

·         Open 2S roar approved Lipo.

·         Battery must be mounted in the stock battery location in the center of the chassis.

·         ROAR Approved 13.5 motor and ROAR Approved ESC in blinky mode.

·         Any full fender street stock car body

·         1” spoiler off deck lid

·         NO Decking

·         Minimum weight is 1500 grams

·         Open motor, open speed control

·         1/10 scale race chassis (GFRP, Customworks, etc.)

·         Open tire rule, except for no 4wd fronts

·         2-cell Lipo

·         No side dams

·         Up to 2 ½’ spoiler off deck lid

·         13.5 Hobbywing JustStock motor and ESC

·         1/10 scale race chassis (GFRP, Customworks, etc.)

·         Open tire rule, except for no 4wd fronts

·         2-cell Lipo

·         No side dams

·         Up to 2 ½’ spoiler off deck lid